Company Details


  •  [Zhejiang,China]
  • Business Type:Manufacturer , Trade Company
  • Main Mark: Worldwide
  • Exporter:61% - 70%
  • Description:Hydrocortisone Sodium Succinate for Injection,Hydrocortisone 100 Mg,Hydrocortisone Powder for Solution
Inquiry Basket ( 0 )


Hydrocortisone Sodium Succinate for Injection,Hydrocortisone 100 Mg,Hydrocortisone Powder for Solution

Home > Products > Finished Drugs > Others Finished Drugs > GMP Hydrocortisone Sodium Succinate for injection 100mg

GMP Hydrocortisone Sodium Succinate for injection 100mg

Share to:  

Product Description

Hydrocortisone may be administered by intravenous injection, by intravenous infusion or by intramuscular injection, the preferred method for initial emergency use being intravenous injection. Following the initial emergency period, consideration should be given to employing a longer-acting injectable preparation or an oral preparation.

Dosage usually ranges from 100 mg to 500 mg depending on the severity of the condition, administered by intravenous injection over a period of one to ten minutes. This dose may be repeated at intervals of 2, 4 or 6 hours as indicated by the patient's response and clinical condition.

In general high-dose corticosteroid therapy should be continued only until the patient's condition has stabilised - usually not beyond 48 to 72 hours. If hydrocortisone therapy must be continued beyond 48 to 72 hours hypernatraemia may occur, therefore it may be preferable to replace Hydrocortisone with a corticosteroid such as methylprednisolone sodium succinate as little or no sodium retention occurs.

Although adverse effects associated with high dose, short-term corticoid therapy are uncommon, peptic ulceration may occur. Prophylactic antacid therapy may be indicated.

Patients subjected to severe stress following corticoid therapy should be observed closely for signs and symptoms of adrenocortical insufficiency.

Corticosteroid therapy is an adjunct to, and not a replacement for, conventional therapy.

In patients with liver disease, there may be an increased effect (see section 4.4) and reduced dosing may be considered.

Elderly patients: Hydrocortisone is primarily used in acute short-term conditions. There is no information to suggest that a change in dosage is warranted in the elderly.

However, treatment of elderly patients should be planned bearing in mind the more serious consequences of the common side-effects of corticosteroids in old age and close clinical supervision is required (See Section 4.4).

Paediatric population: While the dose may be reduced for infants and children, it is governed more by the severity of the condition and response of the patient than by age or body weight but should not be less than 25 mg daily (see Special warnings and special precautions for use).

Preparation of solutions: For intravenous or intramuscular injection prepare the solution aseptically by adding not more than 2 ml of sterile water for injections to the contents of one vial of Hydrocortisone 100 mg, shake and withdraw for use.

For intravenous infusion, first prepare the solution by adding not more than 2 ml of sterile water for injections to the vial; this solution may then be added to 100 ml -1000 ml (but not less than 100 ml) of 5% dextrose in water (or isotonic saline solution or 5% dextrose in isotonic saline solution if patient is not on sodium restriction).

When reconstituted as directed the pH of the solution will range from 7.0 to 8.0 and the appearance of the solution is clear and colourless to almost colourless.

Looking for ideal Hydrocortisone Sodium Succinate for Injection Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the Hydrocortisone 100 Mg are quality guaranteed. We are China Origin Factory of Hydrocortisone Powder for Solution. If you have any question, please feel free to contact us.

Product Categories : Finished Drugs > Others Finished Drugs

Email to this supplier
  • *Subject:
  • *Messages:
    Your message must be between 20-8000 characters
Communicate with Supplier?Supplier
Medic Ren Mr. Medic Ren
What can I do for you?
Contact Supplier